Earth Testing, Megger Testing & Power Factor Testing in Jaipur & Rajasthan
Earth resistance, insulation resistance (Megger) and power factor testing with calibrated instruments and formal test reports for approvals, audits and maintenance.
How Earth, Megger & PF Testing works
Testing is the only way to know whether an electrical installation is actually safe. A good-looking panel can have an earth pit with very high resistance, a cable with degraded insulation or a capacitor bank that no longer corrects power factor. These problems cause shocks, fires, equipment failure and penalties on electricity bills.
Shree Kalyan Enterprises provides on-site electrical testing in Jaipur and across Rajasthan with calibrated instruments. Our test reports record instrument details, method, measured values and acceptance criteria, so they can be used for CEIG approval files, periodic inspections, insurance surveys and internal audits.

What our Earth, Megger & PF Testing service covers
Earth resistance testing
Earth pit and grid resistance by the fall-of-potential or clamp method.
Insulation (Megger) testing
IR testing of cables, motors, transformers and panels at suitable test voltages.
Power factor analysis
PF, harmonics and load logging with a power quality analyser.
APFC performance
Capacitor health and APFC controller settings checked.
Continuity & polarity
Protective conductor continuity and polarity checks.
Test reports
Formal reports with instrument and calibration details.
Documents for Earth, Megger & PF Testing
- Earthing layout / earth pit locations (if available)
- SLD and cable schedule
- Electricity bills (for PF analysis)
- APFC panel details
- Earlier test reports
Reports and approval letters
- Earth resistance test report
- Insulation resistance test report
- Power factor and load analysis
- APFC / capacitor recommendations
- List of failed points and corrective actions
Regulations behind Earth, Megger & PF Testing
- CEA (Measures relating to Safety and Electric Supply) Regulations, 2023
- IS 3043 – Code of practice for earthing
- Relevant IS / IEC standards for insulation testing
- RERC tariff orders on power factor incentives and penalties
Earth, Megger & PF Testing in 6 steps
Some insulation tests require isolation of equipment. We plan these with your maintenance team to keep downtime to a minimum.

- 1
Scope
Points & equipment
- 2
Planning
Shutdown if needed
- 3
Testing
Calibrated instruments
- 4
Analysis
Against criteria
- 5
Report
Values & remarks
- 6
Corrections
Recommended fixes
Questions about Earth, Megger & PF Testing
Answered by our engineers. Ask us if yours is not here.
Ask an engineerWhat is a good earth resistance value?
Acceptable values depend on the type of installation and the applicable standards. Lower is better, and values are judged against the criteria for that installation, which we state in the report.
What is Megger testing?
Megger testing is insulation resistance testing using a high-voltage DC tester. It shows whether cable, motor or transformer insulation is healthy.
How often should earth pits be tested?
At least once a year and after major changes, and more often in dry or corrosive conditions.
Why is my power factor low even with an APFC panel?
Common causes are failed capacitors, wrong controller settings, an undersized bank or harmonics. Logging the load identifies the actual cause.
Are your test reports accepted for CEIG approval?
Our reports include instrument, calibration and method details as typically required for approval files.
Earth, Megger & PF Testing across all 41 districts of Rajasthan
We handle this work with all three DISCOMs, from our Jaipur office. Find your area:
- Jaipur zone (JVVNL)Eastern Rajasthan
- Ajmer zone (AVVNL)Central and southern Rajasthan
- Jodhpur zone (JdVVNL)Western Rajasthan
Cities: Jaipur · Jodhpur · Udaipur · Kota · Ajmer · Bhilwara · Bikaner · Alwar and Bhiwadi · Sikar · Barmer and Balotra


